I have mainly been inserting bullet points inside text box objects within my 'Instructions' pages (tabs), but I will list out some ways you can insert bullet points directly into your spreadsheet as well. Keyboard Shortcut: Alt + 7 (number must be from your number pad) 2. Keyboard Shortcut: Alt + 0149. 3.minor key, AC 93 minus sign (), EX20 misspelled words, adding to dictionary.
![]() Excel Add Bullet Points In Cell How To Make BulletIn the gauge, this small voltage results in rotation of a needle around a pivot. These dials make sense in a mechanical setting: they are activated by small voltages generated by sensors in the equipment. GaugesGauge graphs are based on the numerous dials found in automobile dashboards and aircraft cockpits. In this tutorial I’ll show how to make bullet graphs in Excel, using a simplified approach that works for horizontal and vertical bullet charts. On one side, there are myriad gauge designs on the other are more effective charts, notably Stephen Few’s Bullet Graphs. With the recent obsession with dashboard displays of business data, this struggle has come to a head. They also show only a “right now” value, rather than a historical view afforded by line charts. They take up a lot of space to show very little information, and comparisons among several gauges are difficult to judge with any precision. Dial gauges in a business dashboard are remarkably ineffective. Instead of treating a dashboard as a place where a lot of information is displayed in a limited field of view, they apply the metaphor of cockpit too literally, as if the manager is driving his desk around the company. These dials also make sense in a cockpit: you need to know what’s happening right now, and in general you do not need to compare the values on several dials.Some business dashboard designers have missed the point. ![]() Select the Line chart type with markers, format its marker as a square with dark blue border and fill, and format it to use No Line (left chart below). I’ve formatted Actual as a dark blue bar (which will show up slightly better on screen than a black bar), and Target as a red bar, but these formats will have to be recreated since their chart types will be changed.Right click the Actual series, and choose Change Series Chart Type. Format High, Medium, and Low as light to dark gray bars. It’s a line chart series, so you only get vertical error bars (first chart below). For this thin chart, Excel may make both the chart and the legend too narrow, so adjust the width of the plot area and the legend so both fit nicely (below right).Select the Actual series and add error bars. Since Excel automatically plots Actual on the secondary axis, format the series to appear on the primary axis (below right).Note that all of the above three steps can be accomplished in Excel 2013 in one trip to the Chart Type dialog, but earlier versions need three different formatting steps.Format any of the remaining column chart series (High, Medium, or Low) and set the Overlap to 100 and Gap Width of 50 (below left). Select the XY chart type with markers and no lines, and choose the dash marker using red fill and a red border with thickness of 1.5 instead of the default 0.75, which will eventually look better in the legend (middle chart below). Ssh keygen for github email address using macBut we went to the trouble of formatting our markers to look good in the legend.If we format individual points in a series differently than we format the entire series, the formatting for the entire series stays in the legend. Error bars do not show up in the legend, so the dark blue and red symbols for Actual and Target would disappear. Delete the vertical error bars, and format the horizontal error bars to show both directions, at a value of 0.3, without end caps, with a 1.5-point red line.Sometimes the default error bars are too short to see, so you need to use the dropdown in the top left of the Chart Tools > Format or Layout tab to select the set of error bars you need to format.Now comes a little bit of Excel Chart Magic. It’s an XY scatter chart series, so you get horizontal and vertical error bars (third chart below). If the title of the format dialog or task pane says “Format Data Point”, you are ready to go. Now press Ctrl+1 to format the point. Then click on the marker again or click the right keyboard arrow key, which selects just the single point. Here’s how:Click on the marker for Actual, which selects the whole Actual series. The High, Mid, Low, and Target can be the same or different for each bullet. You need one column per bullet, with High, Mid, and Low, plus Actual and Target for each. Of course, if you don’t need a legend, you could have skipped all the marker formatting we did before, not shown a legend at all, and made the bullet chart even slimmer (below right).The protocol for multiple vertical bullets in a single chart is the same as for a single bullet, with minor adjustments. This hides the marker for the data point in the chart, but leaves the marker in the legend.The result is the left chart below. This hides the Actual marker for the data point in the chart, but leaves the marker in the Actual legend entry.Repeat the single click plus single click technique to select the marker for Target. In the Format Data Point dialog, again choose No Marker for Marker Style. In the Format Data Point dialog, choose No Marker for Marker Style. Since Excel automatically plots Actual on the secondary axis, format the series to appear on the primary axis (below middle). Format any of the remaining column chart series (High, Medium, or Low) and set the Overlap to 100 and Gap Width of 50 (below right).Select the Actual series and add error bars. Select the XY chart type with markers and no lines, and choose the dash marker using red fill and a red border with thickness of 1.5 instead of the default 0.75, which will eventually look better in the legend (left chart below). This messes up the legend, but remembering to set the line to No Line fixes it (below right)Right click the Target series, and choose Change Series Chart Type. Select the Line chart type with markers, format its marker as a square with dark blue border and fill (left chart below). Now press Ctrl+1 to format the point. Then click on the first marker or click the right keyboard arrow key, which selects just the first point. Delete the vertical error bars, and format the horizontal error bars to show both directions, at a value of 0.3, without end caps, with a 1.5-point red line (below right).Now we repeat our little bit of Excel Chart Magic.Click on the Actual series, which selects the whole series. It’s an XY scatter chart series, so you get horizontal and vertical error bars (left chart below). Format the error bars to show the minus direction only with a percentage of 100, without end caps, using the same dark blue for the line, and make the line thick (such as 7.5 points in the right chart below).Select the Target series and add error bars. Again, if you don’t need a legend, you could have skipped all the marker formatting we did before, omitted the legend, and made the bullet chart narrower (below right). This hides the marker for the points in the chart, but leaves the marker in the legend.The result is the left chart below. Click the right arrow key to select the next Target point, and again choose the No Marker option, and repeat for the rest of the Target data points. This hides the Actual marker for the points in the chart, but leaves the marker in the Actual legend entry.Click on the Target series, then click on the first Target marker or click the right arrow key to select the first marker for Target. In the Format Data Point dialog, choose No Marker for Marker Style. Repeat for the rest of the Actual points. Click the right arrow key to select the next point, and again choose the No Marker option.
0 Comments
Leave a Reply. |
AuthorPerry ArchivesCategories |